Notes·Defense & SCIF··8 min read

SAPF vs. SCIF tablet requirements: DoDM 5205.07 and ICD 705 compared

By Rob Pfleghardt · CBR Labs Engineering·Alexandria, VA (CAGE 14Y35)

Special Access Program Facilities (SAPFs) and SCIFs share physical construction baselines, but their Portable Electronic Device (PED) approval chains differ sharply. Here is what SAPSOs and SSOs require before a tablet crosses the threshold.

Bottom Line Up Front (Executive Summary)

Both SCIFs (governed by ICD 705) and SAPFs (governed by DoDM 5205.07) classify any tablet with cameras, microphones, or wireless transceivers as a restricted Portable Electronic Device (PED). While some SCIFs permit MDM-supervised GFE tablets under exception, SAPSOs almost universally require physical board-level removal of all optical, acoustic, and RF silicon backed by per-unit photographic proof.

Key Findings for Procurement & Security Teams
  • ICD 705 and DoDM 5205.07 evaluate physical hardware capability (transducers and transceivers), not software configuration or MDM profile state.
  • SAPF accreditation is compartment-specific; SAP Security Officers (SAPSOs) routinely reject software-only mitigations that a general SSO might accept.
  • Standardizing on a 'Full Six' board-level redaction profile (cameras, mics, speakers, Wi-Fi, Bluetooth, cellular/GPS excised) allows one fleet to serve both SCIF and SAPF bays.
  • Attaching a serial-numbered Certificate of Redaction and internal PCB photography to the PED exception package eliminates most technical RFI cycles.
SAM.gov · CAGE 14Y35 · WOSB · 5–10 Day Turn
Scope this profile

Security managers supporting both Sensitive Compartmented Information Facilities (SCIFs) and Special Access Program Facilities (SAPFs) often discover that a Portable Electronic Device (PED) package approved in one room stalls in the other. While the physical construction standards largely converged under ICD 705 and the Technical Specifications for Construction and Management of Sensitive Compartmented Information Facilities, the operational approval authority for bringing a tablet inside remains distinct.

Understanding how ICD 705 interacts with DoD Manual 5205.07 (Special Access Program Security Manual) saves weeks of back-and-forth between program managers, Information System Security Managers (ISSMs), Special Security Officers (SSOs), and SAP Security Officers (SAPSOs).

Where the baselines overlap: physical capability, not intent

Both ICD 705 and DoDM 5205.07 Volume 3 treat any device with optical, acoustic, or radio-frequency (RF) capture/transmission capability as a controlled hazard inside the perimeter. Neither standard cares what application is installed on the home screen; both evaluate the underlying hardware transducers and transceivers.

If a commercial off-the-shelf (COTS) iPad or Android tablet retains a live microphone capsule, CMOS image sensor, cellular baseband, Bluetooth controller, or Wi-Fi radio die, it is categorized as a recording and transmitting PED by default.

  • Acoustic capture: MEMS microphones and speaker coils capable of microphonic pickup.
  • Optical capture: Front, rear, and IR/TrueDepth camera assemblies.
  • RF emission & geolocation: Wi-Fi (2.4/5/6 GHz), Bluetooth/BLE, Ultra-Wideband (UWB), NFC, GPS/GNSS, and cellular modems.

How SAPF approval differs from standard SCIF accreditation

In a standard SCIF, the Cognizant Security Authority (CSA) and the site SSO evaluate PED exception requests against the facility's Fixed Facility Checklist (FFC) and TEMPEST/technical security countermeasures posture. In a SAPF, the Program Security Officer (PSO) or SAPSO exercises compartment-specific oversight that frequently prohibits software-only mitigations outright.

Where some SCIF accreditors may entertain a Government-Furnished Equipment (GFE) tablet under strict Mobile Device Management (MDM) supervision for low-risk administrative use, SAPF accreditors almost universally reject software toggles. A profile can drift; a missing chip cannot.

The hardware configuration that satisfies both rooms

Programs that standardize on a single 'Dual-Room' hardware redaction profile avoid maintaining separate device pools for SCIF and SAPF bays. That baseline profile removes all six transducer and radio classes at the board level:

  1. Board-level camera excision: Front and rear camera modules removed; apertures plugged and sealed flush.
  2. MEMS microphone removal: All microphone capsules desoldered from the audio bus and acoustic ports sealed.
  3. Speaker driver removal: Internal drivers removed to eliminate both audio output and passive coil microphonics.
  4. Total RF silicon removal: Wi-Fi/Bluetooth combo modules, cellular modems, UWB, NFC, and GPS receivers physically removed from the logic board; antenna runs severed.
  5. Wired data & charging only: Device operates strictly via approved USB-C/Lightning hardwired media or standalone offline workflows.

Building the artifact binder for the SSO and SAPSO

When submitting your PED introduction request, attach unit-level physical evidence rather than vendor marketing sheets. Every CBR Labs tablet ships with a serial-numbered Certificate of Redaction, high-resolution pre- and post-redaction internal board photography tied to the device serial number, and a timestamped chain-of-custody log from our Alexandria, Virginia facility.

Providing the accreditor with macro photographs of the vacant BGA pads where the radio and audio silicon previously sat turns a subjective policy debate into a straightforward visual verification.

Bench-level teardown: how optical, acoustic, and RF buses are isolated

Accreditors reviewing a Portable Electronic Device (PED) package for a Special Access Program Facility (SAPF) or SCIF increasingly ask what happens on the printed circuit board (PCB) rather than accepting a generic statement that components were removed. On modern iPad and Samsung Galaxy Tab architectures, transducers and transceivers sit on distinct high-speed buses that must be cleanly terminated without destabilizing the System-on-Chip (SoC) power management integrated circuit (PMIC).

During a Full-Six board-level redaction at CBR Labs, technicians thermally release the laminated display assembly on a controlled heating platen, remove theEMI shield cans covering the RF and audio sections, and execute physical excision across each subsystem:

  • MIPI CSI-2 Optical Bus: Front, rear, and TrueDepth/IR camera modules are disconnected and physically removed from the chassis. The internal optical windows are plugged with an opaque, non-conductive composite so no external lens path remains.
  • PDM / I2S Audio Input Bus: Every surface-mount MEMS microphone capsule (typically three to five per tablet across top, rear, and side flex cables) is desoldered using precision hot-air rework, leaving the differential clock/data pads open and electrically silent.
  • Class-D Speaker Output Stage: Internal voice-coil speaker assemblies are removed from the acoustic chambers, eliminating both audible playback and reverse microphonic induction.
  • PCIe / SDIO Wireless Transceivers: The Wi-Fi/Bluetooth combo BGA module, Ultra-Wideband (UWB) transceiver, NFC controller, and cellular baseband/RF front-end (if present) are desoldered from the main logic board, and coaxial antenna feed paths are physically severed.

Before the display is re-bonded with OEM-grade structural adhesive, the open logic board is photographed under macro lighting with the device's serial number visible in frame. That photograph becomes part of the permanent accreditation artifact binder.

Field receiving & periodic inspection protocol for SSOs and SAPSOs

Once a redacted tablet cohort arrives at the facility's shipping and receiving desk, the Special Security Officer (SSO) or SAP Security Officer (SAPSO) needs a repeatable intake and periodic re-verification protocol to satisfy ICD 705 and DoDM 5205.07 audit trails:

  1. Cross-check manifest to chassis serial: Verify the manufacturer hardware serial number in Settings -> General -> About against the CBR Labs packing slip and the signed Certificate of Redaction.
  2. Scan the tamper-evident QR verification tag: Verify the unit's CBR-YYYY-NNNN asset tag against the verification record and log the unit into the facility PED register.
  3. Inspect optical apertures and RF state: Confirm front and rear camera apertures are plugged opaque, Settings -> Wi-Fi / Bluetooth are unavailable, and no audio waveform registers in diagnostic capture.
  4. File the four-stage photo packet in the SSP/CONOP: Attach the unit's open-board pre/post photographs to the facility Fixed Facility Checklist (FFC) or SAPF CONOP appendix.
Reference Matrix

SCIF (ICD 705) vs. SAPF (DoDM 5205.07) Tablet Approval Comparison

Control DimensionStandard SCIF (ICD 705)SAPF (DoDM 5205.07)CBR Labs Full-Six Redaction
Primary Approval AuthorityCognizant Security Authority (CSA) / Site SSOSAP Security Officer (SAPSO) / Program Security Officer (PSO)Provides unit-level evidence packet for both authorities
Cameras (Front/Rear/IR)Prohibited unless physically disabled/removedStrictly prohibited; physical removal requiredModules physically excised; apertures plugged flush
Microphones & SpeakersMEMS mics prohibited; speakers often restrictedAll acoustic transducers (mics + speaker coils) restrictedMEMS capsules desoldered; speaker drivers removed
Wireless RF (Wi-Fi/BT/Cell/UWB)Prohibited unless specifically accredited WLANZero-RF baseline standard across compartmentsRF silicon desoldered from PCB; antenna traces cut
Required Audit ArtifactPED exception memo + verification documentationCompartment CONOP + physical modification proofSerialized Certificate of Redaction + internal board photos
Common Questions

Frequently asked questions

Can a tablet approved for a SCIF automatically be carried into a SAPF?

+

No. SAPFs require compartment-specific approval from the SAPSO or PSO under DoDM 5205.07. However, if the tablet has already undergone Full-Six board-level hardware redaction with photographic proof, the same technical evidence packet usually satisfies both accreditors.

Why do SAPSOs require speaker removal in addition to microphone removal?

+

Dynamic speaker drivers contain a diaphragm and voice coil attached to a magnet—electrically, a speaker is a microphone in reverse. Removing both the MEMS microphones and the internal speaker drivers eliminates any passive acoustic-to-electrical transducer on the device.

Does CBR Labs provide open-chassis photos for every single serial number?

+

Yes. Every device redacted at our Alexandria, Virginia facility is photographed at four stages—intake, pre-redaction open board, post-redaction open board showing component removal, and final pack-out—tied to the manufacturer serial number and CBR Labs asset tag.

Does removing the Wi-Fi/Bluetooth BGA module cause iPadOS or Android to boot-loop?

+

No. CBR Labs' board-level rework isolates the transceiver IC while preserving the I2C/SPI pull-ups and PMIC power-good rails required by the bootrom. The tablet boots normally into the OS with wireless interfaces simply reported as unavailable.

How should redacted tablets be stored inside a SCIF or SAPF when not in use?

+

Even after Full-Six hardware redaction, facility CONOPs typically require GFE tablets to be inventoried by serial number at shift change and stored inside the room's accredited perimeter or a GSA-approved security container.

Technical Review & Provenance · CBR Labs LLC

Written and reviewed by Rob Pfleghardt and the bench engineering team at CBR Labs LLC (5927 Tilbury Road, Alexandria, VA 22310). CBR Labs is an active SAM.gov-registered Woman Owned Small Business (CAGE 14Y35 · UEI K4MZG4KC1MY9) performing permanent, board-level hardware redaction on iPad and Android tablets.

SAM.gov Active · CAGE 14Y35 · WOSB

Standardize your SCIF and SAPF tablet profile

Share your PSO or SSO requirements and we will scope a board-level redaction profile with full photographic evidence.

Request a quote